HVAC Damper Types

Manual Damper HVAC Volume Damper Ductwork Fitting.

HVAC Damper Types - Most of us, when we think of an air damper, think of rushing to a freshly lit fireplace to flip the soot covered handle that opens the chimney as the room fills with smoke. The HVAC damper is a simple enough concept, direct or redirect airflow in your air conditioning or exhaust system according to your specific requirements. So why are there so many different styles? They range from $5 to $500, so what’s the difference, and which one do you need?

HVAC Damper Types

Damper, I barely know her?

Basic Manual Volume Damper

These are the most typical of the HVAC ductwork dampers. The purpose of these duct fittings is to adjust the air velocity for specific branches of duct. For example, if you have way too much air coming out of your master bedroom, you can close the damper to that room, either partially or all the way, and the air will be redirected to other parts of the system. Many novices buy these thinking that they can use them to completely shut off a branch of duct, this is not the case.

These volume dampers, even when all the way closed, still allow some air through. You will notice that even when closed there is a small gap all the way around the blade. These are not for closing off a duct completely, they are simply for “balancing” the airflow in a system to the desired levels. Always make sure you tighten the wing nuts and hardware as tightly as possible so that the blade is locked in place, and so you don’t get an annoying rattling or buzzing sound. Lower quality fittings will often buzz and rattle, so make sure you’re not cutting corners on quality!


Manual Volume Damper W/Standoff Handle | HVAC Damper Types

The manual volume damper with standoff handle is required when the sheet metal duct has an external insulation. The standoff handle allows the damper blade to be adjusted without being hindered by the insulation. But, these are also a great option for dust collection systems, paint spray booths, smokers, or any application that requires frequent air flow adjustments. At The Sheet Metal Kid we make them with a slightly thicker gauge of metal, and the handle allows for convenient access and maximum adjustability.

Backdraft Dampers (aka Butterfly Damper) | HVAC Damper Types

The purpose of the backdraft damper is exactly what the name suggests, it blocks air from reversing and blowing back into the vent in the wrong direction. For example, you may put these on a fresh air vent that goes out an exterior wall so that the indoor air can go out, but the outdoor air cannot get back into the conditioned space. There are different designs, but most commonly the back draft damper has a hinge in the center of the balancing blade that only collapses in one direction.

Butterfly Backdraft Damper

Butterfly Backdraft Damper

Barometric Pressure Relief Fitting - Bypass Damper

Barometric Pressure Relief Fitting - Bypass Damper

HVAC Duct Fire Smoke Damper

HVAC Duct Fire Smoke Damper

HVAC Duct Fittings Control Damper Zone

HVAC Duct Fittings Control Damper Zone

Barometric “Bypass” Damper | HVAC Damper Types

These are rather elegantly designed little fittings with no electricity required, and minimal moving parts. They have a handle similar to the “standoff” style, but there is also a weight that can be slid up or down. These dampers open and allow air to escape when a certain barometric pressure is reached, thus equalizing the air pressure on either side of the metal fitting according to how you have adjusted the weight.

Control Dampers (aka Zone Damper) | HVAC Damper Types

The control damper has an electric motor that can open or close the damper when the temperature control system commands. These are often used for optimizing the air conditioning system by adding zones. Zones are designated in a building according to many criteria; occupancy, solar heat gain, fresh air requirements, etc. You may use a zone damper along with an occupancy sensor so that when a space is occupied the zone damper opens, and when it is not occupied, the zone damper is closed, so that air is directed to other zones in the building that are in use.

Fire Damper or Fire/Smoke Damper | HVAC Damper Types

Fire dampers and Fire/Smoke dampers part of the building’s life safety system. They usually require an auxiliary power source that will not be interrupted if the building catches fire. Building codes differ on exactly when these are required, but it’s usually when duct is penetrating a partition of a certain fire rating. The fire damper automatically closes ventilation when it gets the signal that there is a fire. This closes the air duct so that the fire isn’t fed by the ac system, and to slow the fire from spreading to other areas. Fire/smoke dampers are essentially the same thing, except that they also have smoke sensor, in addition to the fire sensor.

To learn more about heating systems and HVAC use this resource.

See the About the Author page for information about the author of this article.

Share your HVAC Photos or ask a question about your HVAC System by uploading a photo of it.

Photo Uploads
Enter your name so we can credit you
If you have a website enter your website URL for additional credit
If you want to include a description then do so here.
Drop a file here or click to upload Choose File
Maximum upload size: 33.55MB
jpe, jpeg, jpg, gif, png, bmp, docx, doc, txt and PDF files allowed to be uploaded. Limit 15 files total and 100 mb/s max size.

Check High Performance HVAC’s handy calculators located throughout the the site.

Use our handy calculator to see how many BTU's your natural gas appliances are producing: