Gas Furnace Components - Gas Valve TroubleshootingGas Valve Troubleshooting - Gas valves used in modern state-of-the-art residential gas furnaces are typically controlled via a state-of-the-art electronic ignition control or a printed circuit board. Other types of gas valves include the standing pilot gas valve.

Gas valves can be found on gas furnaces, gas-fired steam boilers or hot water boilers, and gas-fired water heaters. With gas valve troubleshooting and any “gas valve” issues, safety is always first.

When troubleshooting a gas valve, the technician should only be concerned with input to the gas valve and output of the gas valve, whether it is an electronic module or circuit board controlled gas valve, or a standing pilot gas valve. The input with gas valve troubleshooting includes ensuring the safety circuit is good.

 

Gas Valve Troubleshooting | Electronic Ignition Gas Valve Troubleshooting

Gas valve troubleshooting looks for a problem. If something is wrong with the internal components of the gas valve, the gas valve should be replaced. The gas valve cannot be repaired in the field. Only the gas valve manufacturer or someone certified by the manufacturer of the gas valve can make repairs. Then re-certifying the safety of the gas valve.

This also applies to gas valves that have been submerged underwater due to flooding. Flooding of your boiler or gas furnace or water heater. If the gas valve is found to be defective internally in any way, you need a new gas valve. After a gas valve has been submerged or partially submerged, replace it with a new gas valve. That is a basic safety rule that all technicians or DIYers should follow when gas valve troubleshooting.

Electronic Ignition Gas Valve Basics

ignition control module with flash codes

Ignition Control Module by White-Rodgers (Now Emerson Electric)

Any electronic component has a basic troubleshooting rule that every technician should follow when efficiently troubleshooting any electronic ignition gas component. The board should have an input and an output to follow a basic control sequence. The basic furnace control sequence for an electronic ignition control board typically originates at a thermostat for a call for heat. By initiating a call for heat from the thermostat the technician begins the process of the sequence of operation.

This completes a circuit to the main control. The electronic control or printed circuit board for the gas furnace. The control sequence of operation for an electronic ignition gas furnace will always include safeties to be proven before the gas electronic control board or printed circuit board allows any output to the gas valve. The safety circuit in many gas furnaces including boilers will include but are not limited to the following:

Components and Safety Switches of the Furnace

Gas Valve Repair​The following components work in conjunction with the gas valve. With gas valve issues, including gas valve troubleshooting, all safety switches must be closed. All checks should be done to ensure the safeties are good before gas valve troubleshooting.

  • Forced Draft or Induced Draft Pressure Switch
  • Draft hood limit switches
  • Limit switches in or near the heat exchanger
  • Limit switches near the furnace blower motor
  • Any other safety switch that can be opened by temperature or pressure. A switch that is integral to the safety circuit of the gas furnace. Each brand of furnace is engineered differently. See the pictorial or the ladder diagram for all safeties engineered in the gas furnace. These diagrams can be found inside the control of the furnace.

Safeties for the Furnace and Ignition

In “gas heating repair” safety is always first. Once all the safeties are proven the electronic ignition control board will send a signal to the gas valve. The command will be to open either the main valve (if it is direct ignition) or to light the intermittent pilot light. Whether it is direct ignition or intermittent pilot light the flame must be proven through a flame sensor. Proven to keep the sequence from restarting and trying the ignition sequence again. If the flame cannot be proven then the system will shut down for a predetermined amount of time. +/- 4 hours is typical.

If a flame cannot be proven the manufacturer of the controls and the furnace do not want the gas furnace continuously trying for ignition. This is because a dangerous amount of gas can accumulate resulting in serious damage to a structure or people. If the flame is proven the sequence continues until the thermostat is satisfied and everything shuts down until the thermostat again calls for heat and then the whole sequence has to be proven over again so the furnace can provide heat.

Gas Valve Issues

Manual Reset Limit Switch

Standing Pilot Gas Valves

Everything that applies to the electronic ignition sequence of operation by the way of the safety circuit must be proven before the gas furnace will allow the gas valve to fire the main burners to provide heat. The difference is the standing pilot gas furnace always has a pilot light on. First. test the thermocouple. Adjust pilot flame as necessary to make sure the thermocouple is getting enough heat. If it still doesn’t work then you could have a bad coil in the gas valve.

Again, if you are not properly trained in the functionality of gas furnaces and basic safety practices you should call a professional. See our disclaimer. Working on HVAC equipment can be hazardous. Call a professional whenever your gas furnace is not working properly.

High Performance HVAC

Gas Furnace Components – Gas Valve Troubleshooting